SPC6xxx configuration: Difference between revisions
No edit summary |
No edit summary |
||
Line 10: | Line 10: | ||
In the SPC6000 web-based configuration tool set in “Full Engineer” mode (refer to | In the SPC6000 web-based configuration tool set in “Full Engineer” mode (refer to | ||
the SPC6000 documentation), note the following parameters: | the SPC6000 documentation), note the following parameters: | ||
* In '''Settings -> Comms -> Ethernet''', set the SPC6000 IP addressing parameters ('IP address') | * In '''Settings -> Comms -> Ethernet''', set the SPC6000 IP addressing parameters ('IP address') | ||
* In '''Settings -> Comms -> EDP''', '''Add''' a receiver to the list and specify: | * In '''Settings -> Comms -> EDP''', '''Add''' a receiver to the list and specify: | ||
** '''Receiver ID''' (unique number). The Receiver ID must match the SIWENOID setting | ** '''Receiver ID''' (unique number). The Receiver ID must match the SIWENOID setting | ||
** '''Network Address''' (IP address) of the SIWENOID server | ** '''Network Address''' (IP address) of the SIWENOID server | ||
* In '''Settings -> Comms -> EDP''', select and Edit the receiver entry and specify: | * In '''Settings -> Comms -> EDP''', select and Edit the receiver entry and specify: | ||
Line 20: | Line 20: | ||
** '''Requeue Event''' must be checked | ** '''Requeue Event''' must be checked | ||
** '''Event filter''' list must be all checked | ** '''Event filter''' list must be all checked | ||
* In '''Settings -> Timers''', make sure that '''Dialer delay''' is set to zero, else a delay occurs before alarms | * In '''Settings -> Timers''', make sure that '''Dialer delay''' is set to zero, else a delay occurs before alarms get transmitted to the SIWENOID. | ||
get transmitted to the SIWENOID. | |||
'Generating the SPC export file' | 'Generating the SPC export file' | ||
* In '''File -> Download''', | * In '''File -> Download''', Browse and download the file | ||
Browse and download the file | |||
---- | ---- | ||
When the web tool is connected to the SPC6000 unit in Full Engineer mode, | When the web tool is connected to the SPC6000 unit in Full Engineer mode, |
Revision as of 15:08, 6 January 2014
Language: | English • magyar |
---|
Previous chapter-> Lantronix configuration / Next chapter-> CCTV configuration
SPC5300 and SP6xxx tool settings
The SPC6000 configuration tool is a web application that works with an Internet browser. The most common browser, Internet Explorer (IE), requires however a special setting: – In Tools, Internet Options, and then Advanced tab. In the option list, search for the Security options and enable Do not save encrypted pages to disk.
In the SPC6000 web-based configuration tool set in “Full Engineer” mode (refer to the SPC6000 documentation), note the following parameters:
- In Settings -> Comms -> Ethernet, set the SPC6000 IP addressing parameters ('IP address')
- In Settings -> Comms -> EDP, Add a receiver to the list and specify:
- Receiver ID (unique number). The Receiver ID must match the SIWENOID setting
- Network Address (IP address) of the SIWENOID server
- In Settings -> Comms -> EDP, select and Edit the receiver entry and specify:
- In the Network section, the Network port (UDP port). The Network port must match the SIWENOID setting.
- In the Event section, the Protocol version that must be Version 2
- Primary Receiver must be checked
- Requeue Event must be checked
- Event filter list must be all checked
- In Settings -> Timers, make sure that Dialer delay is set to zero, else a delay occurs before alarms get transmitted to the SIWENOID.
'Generating the SPC export file'
- In File -> Download, Browse and download the file
When the web tool is connected to the SPC6000 unit in Full Engineer mode, then no alarm messages are transmitted to SIWENOID.
Previous chapter-> Project backup/restore / Next chapter-> CCTV configuration