CerberusPro configuration Siwenoid v2 - Revision history

SWNadmin2: /* Configuring CerberusPro in stand alone mode */

2019-08-23T07:44:57Z

Configuring CerberusPro in stand alone mode

← Older revision		Revision as of 07:44, 23 August 2019
Line 24:		Line 24:
	[[Image: Route.jpeg \|left\|thumb\|700px]] It is necessery to create a route inside the GAP (under overview tab) by setting up the Destination address (Pointing to Siwenoid's subnet, or IP of the Siwenoid client PC), Network mask and Gateway(CerberusPro's subnet router IP).		[[Image: Route.jpeg \|left\|thumb\|700px]] It is necessery to create a route inside the GAP (under overview tab) by setting up the Destination address (Pointing to Siwenoid's subnet, or IP of the Siwenoid client PC), Network mask and Gateway(CerberusPro's subnet router IP).
	<br style="clear: both" />		<br style="clear: both" />
	~~Ha nem jönne létre a kapcsolat akkor ezt a route beállítást is meglehet próbálni~~! (Destination address+netmask: 0.0.0.0, a Gateway ~~marad az alhálózat routerének címe~~!)		Another option if you weren't connected! (Destination address+netmask: 0.0.0.0, Gateway: subnet router address!)
	<br style="clear: both" />		<br style="clear: both" />
	[[Image:Routecerberus.jpg\|left\|thumb\|700px]]		[[Image:Routecerberus.jpg\|left\|thumb\|700px]]

SWNadmin2 at 07:42, 23 August 2019

2019-08-23T07:42:19Z

← Older revision		Revision as of 07:42, 23 August 2019
Line 23:		Line 23:
	<br style="clear: both" />		<br style="clear: both" />
	[[Image: Route.jpeg \|left\|thumb\|700px]] It is necessery to create a route inside the GAP (under overview tab) by setting up the Destination address (Pointing to Siwenoid's subnet, or IP of the Siwenoid client PC), Network mask and Gateway(CerberusPro's subnet router IP).		[[Image: Route.jpeg \|left\|thumb\|700px]] It is necessery to create a route inside the GAP (under overview tab) by setting up the Destination address (Pointing to Siwenoid's subnet, or IP of the Siwenoid client PC), Network mask and Gateway(CerberusPro's subnet router IP).
			<br style="clear: both" />
			Ha nem jönne létre a kapcsolat akkor ezt a route beállítást is meglehet próbálni! (Destination address+netmask: 0.0.0.0, a Gateway marad az alhálózat routerének címe!)
			<br style="clear: both" />
			[[Image:Routecerberus.jpg\|left\|thumb\|700px]]
	<br style="clear: both" />		<br style="clear: both" />


	== Configuring SIWENOID in stand alone mode ==
			=== Configuring SIWENOID in stand alone mode ===
	[[Image:Cerberusproleiras_Angol.png\|left\|thumb\|700px]]		[[Image:Cerberusproleiras_Angol.png\|left\|thumb\|700px]]
	<br style="clear: both" />		<br style="clear: both" />

SWNadmin2 at 11:08, 10 September 2018

2018-09-10T11:08:29Z

← Older revision		Revision as of 11:08, 10 September 2018
Line 1:		Line 1:
	{{Languages\|CerberusPro_configuration_Siwenoid_v2}}		{{Languages\|CerberusPro_configuration_Siwenoid_v2}}
	~~''Previous chapter-> [[Project backup/restore]] / Next chapter-> [[Satel configuration]]''~~
	__TOC__		__TOC__

SWNadmin2 at 11:07, 10 September 2018

2018-09-10T11:07:49Z

← Older revision		Revision as of 11:07, 10 September 2018
Line 1:		Line 1:
	{{Languages\|~~CerberusPro configuration~~}}		{{Languages\|CerberusPro_configuration_Siwenoid_v2}}
	''Previous chapter-> [[Project backup/restore]] / Next chapter-> [[Satel configuration]]''		''Previous chapter-> [[Project backup/restore]] / Next chapter-> [[Satel configuration]]''
	__TOC__		__TOC__

SWNadmin2: /* Configuring SIWENOID in stand alone mode */

2018-09-10T10:52:07Z

Configuring SIWENOID in stand alone mode

← Older revision		Revision as of 10:52, 10 September 2018
Line 38:		Line 38:

	If it is required, UDP port field can be filled when the Control unit and the software is not in the same subnet.		If it is required, UDP port field can be filled when the Control unit and the software is not in the same subnet.


	[[Image:CERBIINPORT_ANGOL.png\|left\|thumb\|700px]]		[[Image:CERBIINPORT_ANGOL.png\|left\|thumb\|700px]]

SWNadmin2 at 10:51, 10 September 2018

2018-09-10T10:51:52Z

← Older revision		Revision as of 10:51, 10 September 2018
Line 42:		Line 42:
	<br style="clear: both" />		<br style="clear: both" />

			A SibX file can contain datapoints of more than one control unit. An import always fetch only one control unit at a time.

	Import a Sibx file by click on the Import metafile button.		Import a Sibx file by click on the Import metafile button.
	~~A SibX file can contain datapoints of more than one control unit. An import always fetch only one control unit at a time.~~
	~~Use the popup menu on the container. Select "Update from metafile".~~ Now set the id's of the control unit you want to import. Device ID must be equal the control unit address, and Device address must be equal the BACnet ID of control unit. If you have more than one control unit in a SibX then repeat these steps and set the id's of control units one by one.		Now set the id's of the control unit you want to import.

			Device ID must be equal the control unit address, and Device address must be equal the BACnet ID of control unit.

			If you have more than one control unit in a SibX then repeat these steps and set the id's of control units one by one.


	~~<br style="clear: both" />~~
	Finally each control units and their datapoint will be included in the container.		Finally each control units and their datapoint will be included in the container.

SWNadmin2 at 10:50, 10 September 2018

2018-09-10T10:50:28Z

← Older revision		Revision as of 10:50, 10 September 2018
Line 30:		Line 30:
	[[Image:Cerberusproleiras_Angol.png\|left\|thumb\|700px]]		[[Image:Cerberusproleiras_Angol.png\|left\|thumb\|700px]]
	<br style="clear: both" />		<br style="clear: both" />

	In the Phyiscal structure settings (File-Settings-Physical structure) add a new container with the + icon. Give it a name, choose the handler type CerberusProMP5, then the protocol type which is Siemens BACnet.		In the Phyiscal structure settings (File-Settings-Physical structure) add a new container with the + icon. Give it a name, choose the handler type CerberusProMP5, then the protocol type which is Siemens BACnet.
	Host IP is the address of the control unit, the BACnet port is 43808 by default. Subnet by default is 255.255.255.0, this should work for simple systems.Local address can be used only if your computer has more than one Ethernet interface. Normally it should be left empty. If it is required, UDP port field can be filled when the Control unit and the software is not in the same subnet.

			Host IP is the address of the control unit, the BACnet port is 43808 by default.

			Subnet by default is 255.255.255.0, this should work for simple systems.Local address can be used only if your computer has more than one Ethernet interface. Normally it should be left empty.

			If it is required, UDP port field can be filled when the Control unit and the software is not in the same subnet.

	[[Image:CERBIINPORT_ANGOL.png\|left\|thumb\|700px]]		[[Image:CERBIINPORT_ANGOL.png\|left\|thumb\|700px]]

SWNadmin2 at 10:49, 10 September 2018

2018-09-10T10:49:53Z

← Older revision		Revision as of 10:49, 10 September 2018
Line 25:		Line 25:
	[[Image: Route.jpeg \|left\|thumb\|700px]] It is necessery to create a route inside the GAP (under overview tab) by setting up the Destination address (Pointing to Siwenoid's subnet, or IP of the Siwenoid client PC), Network mask and Gateway(CerberusPro's subnet router IP).		[[Image: Route.jpeg \|left\|thumb\|700px]] It is necessery to create a route inside the GAP (under overview tab) by setting up the Destination address (Pointing to Siwenoid's subnet, or IP of the Siwenoid client PC), Network mask and Gateway(CerberusPro's subnet router IP).
	<br style="clear: both" />		<br style="clear: both" />


	== Configuring SIWENOID in stand alone mode ==		== Configuring SIWENOID in stand alone mode ==
	[[Image:Cerberusproleiras_Angol.png\|left\|thumb\|700px]] Create a new container in SIWENOID. Select control unit type, and select protocol. There are different protocol for <MP5 and >MP5. Be sure to use the appropriate. Host address is the address of CerberusPro control unit. Subnet is the network mask of BACnet protocol. 47808 is the default BACnet port number. Local address can be used only if your computer has more than one ethernet interface. Normally it should be left empty. Local Device ID is the SIWENOID (as a BACnet client) BACnet ID. This should align the settings of CerberusPro FSX72xx editor parameters. If it is required, UDP port field can be filled when the Control unit and Siwenoid is not in the same subnet.		[[Image:Cerberusproleiras_Angol.png\|left\|thumb\|700px]]
	<br style="clear: both" />		<br style="clear: both" />
	~~[[Image:CERBIINPORT_ANGOL.png\|left\|thumb\|700px]]A SibX file can contain datapoints of more than one control unit~~. ~~An import always fetch only one control unit at~~ a ~~time.~~		In the Phyiscal structure settings (File-Settings-Physical structure) add a new container with the + icon. Give it a name, choose the handler type CerberusProMP5, then the protocol type which is Siemens BACnet.
	~~Use~~ the ~~popup menu on~~ the ~~container~~. ~~Select "Update from metafile". Now set~~ the ~~id's~~ of the control unit ~~you want to import~~. ~~Device ID must be equal the control unit address~~, ~~and Device~~ address ~~must~~ be ~~equal the BACnet ID of control unit. If you have~~ more than one ~~control~~ unit ~~in a SibX then repeat these steps~~ and ~~set~~ the ~~id's of control units one by one.~~		Host IP is the address of the control unit, the BACnet port is 43808 by default. Subnet by default is 255.255.255.0, this should work for simple systems.Local address can be used only if your computer has more than one Ethernet interface. Normally it should be left empty. If it is required, UDP port field can be filled when the Control unit and the software is not in the same subnet.
	~~<br style="clear: both" />~~
	~~Finally each control units and their datapoint will be included~~ in the ~~container~~.

			[[Image:CERBIINPORT_ANGOL.png\|left\|thumb\|700px]]
	<br style="clear: both" />		<br style="clear: both" />

	~~== Configuring CerberusPro in SAFEDLINK subnets ==~~
	~~[[Image:bacnet.png\|left\|thumb\|250px]]~~

	~~<br style=~~"~~clear: both~~" />		Import a Sibx file by click on the Import metafile button.
			A SibX file can contain datapoints of more than one control unit. An import always fetch only one control unit at a time.
			Use the popup menu on the container. Select "Update from metafile". Now set the id's of the control unit you want to import. Device ID must be equal the control unit address, and Device address must be equal the BACnet ID of control unit. If you have more than one control unit in a SibX then repeat these steps and set the id's of control units one by one.

	~~''Previous chapter-> [[Project backup/restore]] / Next chapter-> [[Satel configuration]]''~~

	~~[[Category~~:~~Commissioning]]~~		<br style="clear: both" />
			Finally each control units and their datapoint will be included in the container.

SWNadmin2: /* Configuring SIWENOID in stand alone mode */

2018-09-10T10:36:17Z

Configuring SIWENOID in stand alone mode

← Older revision		Revision as of 10:36, 10 September 2018
Line 27:		Line 27:

	== Configuring SIWENOID in stand alone mode ==		== Configuring SIWENOID in stand alone mode ==
	[[Image:~~GD_015~~.png\|left\|thumb\|~~250px~~]] Create a new container in SIWENOID. Select control unit type, and select protocol. There are different protocol for <MP5 and >MP5. Be sure to use the appropriate. Host address is the address of CerberusPro control unit. Subnet is the network mask of BACnet protocol. 47808 is the default BACnet port number. Local address can be used only if your computer has more than one ethernet interface. Normally it should be left empty. Local Device ID is the SIWENOID (as a BACnet client) BACnet ID. This should align the settings of CerberusPro FSX72xx editor parameters. If it is required, UDP port field can be filled when the Control unit and Siwenoid is not in the same subnet.		[[Image:Cerberusproleiras_Angol.png\|left\|thumb\|700px]] Create a new container in SIWENOID. Select control unit type, and select protocol. There are different protocol for <MP5 and >MP5. Be sure to use the appropriate. Host address is the address of CerberusPro control unit. Subnet is the network mask of BACnet protocol. 47808 is the default BACnet port number. Local address can be used only if your computer has more than one ethernet interface. Normally it should be left empty. Local Device ID is the SIWENOID (as a BACnet client) BACnet ID. This should align the settings of CerberusPro FSX72xx editor parameters. If it is required, UDP port field can be filled when the Control unit and Siwenoid is not in the same subnet.
	<br style="clear: both" />		<br style="clear: both" />
	A SibX file can contain datapoints of more than one control unit. An import always fetch only one control unit at a time.		[[Image:CERBIINPORT_ANGOL.png\|left\|thumb\|700px]]A SibX file can contain datapoints of more than one control unit. An import always fetch only one control unit at a time.
	~~[[Image:SINTESO0001.png\|left\|thumb\|500px]]~~ Use the popup menu on the container. Select "Update from metafile". Now set the id's of the control unit you want to import. Device ID must be equal the control unit address, and Device address must be equal the BACnet ID of control unit. If you have more than one control unit in a SibX then repeat these steps and set the id's of control units one by one.		Use the popup menu on the container. Select "Update from metafile". Now set the id's of the control unit you want to import. Device ID must be equal the control unit address, and Device address must be equal the BACnet ID of control unit. If you have more than one control unit in a SibX then repeat these steps and set the id's of control units one by one.
	<br style="clear: both" />		<br style="clear: both" />
	Finally each control units and their datapoint will be included in the container.		Finally each control units and their datapoint will be included in the container.

	<br style="clear: both" />		<br style="clear: both" />

	== Configuring CerberusPro in SAFEDLINK subnets ==		== Configuring CerberusPro in SAFEDLINK subnets ==
	[[Image:bacnet.png\|left\|thumb\|250px]]		[[Image:bacnet.png\|left\|thumb\|250px]]

SWNadmin2: Created page with "{{Languages|CerberusPro configuration}} ''Previous chapter-> Project backup/restore / Next chapter-> Satel configuration'' TOC == Configuring CerberusPro in stan..."

2018-09-10T10:31:16Z

Created page with "{{Languages|CerberusPro configuration}} ''Previous chapter-> Project backup/restore / Next chapter-> Satel configuration'' __TOC__ == Configuring CerberusPro in stan..."

New page

{{Languages|CerberusPro configuration}}
''Previous chapter-> [[Project backup/restore]] / Next chapter-> [[Satel configuration]]''
__TOC__

== Configuring CerberusPro in stand alone mode ==
CerberusPro (SIEMENS) control unit uses Bacnet protocol to communicate with Siwenoid. Communication settings can be done in FXS72xx editor of CerberusPro control unit.
 
[[Image:Sinteso_1_network_tree.png|left|thumb|300px]] Open network settings of a CerberusPro. In this tutorial we discuss a basic configuration when a SIWENOID and a CerberusPro control unit are in the same network segment.
 
[[Image:_sinteso_1_global_Bacnet_config.png|left|thumb|700px]] First check global BACnet configuration. These settings should be used for proper communication.
 
[[Image:_sinteso_1_Bacnet_client_config.png|left|thumb|700px]] BACnet device ID is the SIWENOID's (as a BACnet client) address. This address has to be set in SIWENOID container definition.
 
[[Image:_sinteso_1_FC_ethernet.png|left|thumb|300px]] Set the IP address of your control unit. This parameter should also be set in thee container definition of SIWENOID.
 
[[Image:_sinteso_1_Ethernet_subnet.png|left|thumb|200px]] Set the network mask of control unit ethernet interface. SIWENOID should be in the same network segment as the control unit.
 
[[Image:_sinteso_1_Bacnet_device_object.png|left|thumb|300px]] This address field is the BACnet address of the CerberusPro control unit. This is important when you import a SibX file into SIWENOID.
 
[[Image:_sinteso_1_Bacnet_device_object_details.png|left|thumb|700px]] Usually you have to leave this field on default. (BBMD should be used when the control unit and SIWENOID are not in the same network segment.)
 
[[Image: Assign.png |left|thumb|700px]] In order to make CerberusPro communicate with Siwenoid from a subnet(Control unit's subnet) to another subnet(Siwenoid's subnet) a GAP creation is necessery in 'Functions' submenu.
 
[[Image: Route.jpeg |left|thumb|700px]] It is necessery to create a route inside the GAP (under overview tab) by setting up the Destination address (Pointing to Siwenoid's subnet, or IP of the Siwenoid client PC), Network mask and Gateway(CerberusPro's subnet router IP).
 

== Configuring SIWENOID in stand alone mode ==
[[Image:GD_015.png|left|thumb|250px]] Create a new container in SIWENOID. Select control unit type, and select protocol. There are different protocol for <MP5 and >MP5. Be sure to use the appropriate. Host address is the address of CerberusPro control unit. Subnet is the network mask of BACnet protocol. 47808 is the default BACnet port number. Local address can be used only if your computer has more than one ethernet interface. Normally it should be left empty. Local Device ID is the SIWENOID (as a BACnet client) BACnet ID. This should align the settings of CerberusPro FSX72xx editor parameters. If it is required, UDP port field can be filled when the Control unit and Siwenoid is not in the same subnet.
 
A SibX file can contain datapoints of more than one control unit. An import always fetch only one control unit at a time.
[[Image:SINTESO0001.png|left|thumb|500px]] Use the popup menu on the container. Select "Update from metafile". Now set the id's of the control unit you want to import. Device ID must be equal the control unit address, and Device address must be equal the BACnet ID of control unit. If you have more than one control unit in a SibX then repeat these steps and set the id's of control units one by one.
 
Finally each control units and their datapoint will be included in the container.

 
== Configuring CerberusPro in SAFEDLINK subnets ==
[[Image:bacnet.png|left|thumb|250px]]

 

''Previous chapter-> [[Project backup/restore]] / Next chapter-> [[Satel configuration]]''

[[Category:Commissioning]]

CerberusPro configuration Siwenoid v2 - Revision history

SWNadmin2: /* Configuring CerberusPro in stand alone mode */

SWNadmin2 at 07:42, 23 August 2019

SWNadmin2 at 11:08, 10 September 2018

SWNadmin2 at 11:07, 10 September 2018

SWNadmin2: /* Configuring SIWENOID in stand alone mode */

SWNadmin2 at 10:51, 10 September 2018

SWNadmin2 at 10:50, 10 September 2018

SWNadmin2 at 10:49, 10 September 2018

SWNadmin2: /* Configuring SIWENOID in stand alone mode */

SWNadmin2: Created page with "{{Languages|CerberusPro configuration}} ''Previous chapter-> Project backup/restore / Next chapter-> Satel configuration'' __TOC__ == Configuring CerberusPro in stan..."

SWNadmin2: Created page with "{{Languages|CerberusPro configuration}} ''Previous chapter-> Project backup/restore / Next chapter-> Satel configuration'' TOC == Configuring CerberusPro in stan..."